Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Pedals

$6.50
The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.
$7.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
$9.00
Dimension Nylon Basic Toe Straps -Durable metal buckle -Multi-purpose strap can also be used as a lash strap for bike touring or rear rack (caution must be used to keep the strap tail out of the wheel) - 450mm
$9.99
Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads
$9.99
Customize and optimize the shoe/pedal interface. - Refine the interface between the shoe tread and pedal body - Four (4) contact sleeves - 1mm thickness
$9.99
Dimension Junior Pedals. - Molded nylon, 1-piece, caged-type pedals - Built-in reflectors, will not accept toe clips - Overall pedal size is 80 x 60mm - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 230g (9/16-inch); 304g (1/2-inch)
$9.99
Dimension Toe Straps. - Durable metal buckle - Multi-purpose strap can also be used as a lash strap for bike touring or rear rack (caution: must be used to keep the strap tail out of the wheel) - 440mm length
$10.00
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
$10.00
RaceFace Chester Pedal Pin Kit 20 Pins Black
$10.00 - $12.00
Coffee Shop Caps protect your Speedplay cleats from wear caused by walking. The caps snap over Speedplay's Light Action cleats and provide a barrier against dirt, protection for floors, and safer traction when walking. Speedplay Coffee Shop Caps are lightweight, constructed of tough, molded elastomer and can conveniently be carried in a jersey pocket.
$11.00
Dimension Mini Toe Clips - Toe clips do not accept toe straps - Sold as a pair - Mounting hardware for the toe-clip is included
$11.00
Dimension Toe Clips and Straps Set. Includes: - 4 bolts - 4 nuts (washers included) - 2 nylon toe straps - 2 toe clips
$11.99
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$11.99
Crank boots designed for RaceFace Next SL G5 cranksets.
$12.99
Replacement pin set for Race Face Atlas and Aeffect pedals.
$13.00
The DELTA standard requires a rotational movement of the foot toward the outside or inside for disengagement. This function improves cyclist's safety; no body or bearing prevents disengagement toward the inside. Compatible with non-KEO LOOK pedals, their contact area is wide for optimal comfort. They also feature a memory positioner to aid when changing cleats. - Use: Road & Indoor Bike - Material: Polyacetal + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 75g
$13.00
The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.
$14.00
The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat
$14.95
Cleat screws are intended for proper installation of the Cleat Wedge. Designed to withstand high torque levels, creating a secure and reliable connection between the rider and the bike. Available in different lengths and styles to fit most pedal systems. - 10mm SPD/MTB compatible cleat screws - 4mm Hex countersunk M5x0.8 - Compatible with most 2-hole cleats - Black oxide-coated carbon steel - 25 pieces
$14.99
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present
$16.00
Dimension City Pedals. - Built-in reflectors, will not accept toe clips - Molded nylon; 1-piece, caged-type pedal - Slip-resistant surface
$16.00
Dimension Mountain Basic Pedals. - Molded nylon 1-piece, caged-type pedal with reflectors - Accepts toe clips - Hang tag packaging - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 330g
$16.00
The Cleat Shim-Spacer helps compensate for leg length discrepancies.
$17.00
- Extend the life of your iSSi Thump pedals by replacing beat-up or missing pins with the Thump Replaceable Pin Kit. - Includes 36 steel pins and 2mm spacers to replace both sides of two pedals - The standard pin height out of the box is 3mm with a 2mm spacer. For more traction, remove the spacer under the pin head to increase pin height to 5mm.
$17.10
Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.
$19.00
Reliable and Durable 2-Bolt Cleat Small details make a big difference—especially when it comes to mountain biking. Worn-out cleats can lead to poor pedal function including premature or stubborn release. But swap on a new set of Shimano SM-SH51 Cleats and you know they're purpose-built to work seamlessly with nearly all Shimano SPD Pedals, delivering long-lasting performance thanks to their heat treated forged steel construction that will stand up to even the harshest riding conditions. Features: - Shimano SM-SH51 SPD Cleats come stock with all Shimano SPD pedals and are the go-to choice for mountain bikers, indoor cyclists, and anyone looking for a durable and reliable 2-bolt cleat. - Customizable: Engineered specifically to work with nearly all Shimano SPD pedals, which allow you to micro-adjust the spring force required to clip in and out of your pedals - Secure Engagement: Deliver 4 degrees of float, which assures just the right amount of movement while also providing a secure connection to your bike - Ease of Disengagement: Feature a 13-degree clip-out angle, allowing you to quickly get out of your pedals when the need arises - Built to Last: Made from heat treated forged steel that delivers durable long-lasting performance even under the most severe riding conditions PREDICTABLE ENGAGEMENT With 4 degrees of float, Shimano SM-SH51 Cleats permit just the right amount of movement for critical on-the-fly weight shifts while still delivering the secure cleat-pedal engagement needed to confidently tackle technical terrain. USER FRIENDLY Shimano SM-SH51 Cleats are compatible with nearly all Shimano SPD pedals, which allow you to micro-adjust how hard or easy it is to clip in and out, providing an unmatched level of customization. These cleats also feature a 13-degree clip-out angle, meaning with the simple outward twist of your heel you can quickly get out of your pedals when the need arises.
$19.99
Dimension Cruiser/Comfort Pedals. - Forged aluminum platform-type body with slip-resistant surface and built-in reflectors - Platform size is 105.5 x 74mm - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 448g
$19.99
Dimension Mountain Sport Pedals. - Molded nylon pedal body - Accepts toe clips - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly - Weight: 290g
$20.00
Wellgo Clipless Cleats for SPD Style pedals.
$21.00
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK cleats provide a 13° angle of disengagement and allow for unidirectional release only. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Lateral - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$21.00
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$22.00
- The ATAC 13/17° cleat works with all TIME mountain pedals. - Included with all mountain pedal models numbered "6" and higher - Release angles of 13 degrees or 17 degrees depending on how the cleat is set up on the shoe - Compatible with all two-hole cycling shoes.
$24.99
Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s
$24.99
A revolution in performance and reliability. - The kit includes premium internal components: - Inner spindle seal x 2 - Outer spindle seal x 2 - Inner Igus solid bearing x 2 - Outer Enduro cartridge bearing x 2 - Spindle nut x 2 - Outer bearing carrier x 2 - Compatibility: Doubleshot (2016), Doubleshot 2 (2017+), Soubleshot 3 (2017+)
$24.99
A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)
$24.99
Kit Includes premium components: - Inner cartridge bearing x 2 - Outer cartridge bearing x 2 - Igus solid bearing x 2 - Inner seal x 2 - Bearing locknut x 2 - Spindle screw (Left) x 1 - Spindle screw (Right) x 1
$26.00
Dimension Mountain Compe Pedals. - Forged aluminum body - Accepts toe clips - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 335g
$26.00
- Look, Kéo 2 Max, Blades
$26.99
Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals
$26.99
Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees
$26.99
Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees
$27.00
The KEO GRIP cleats closely resemble the KEO CLEAT model, yet they boast the added feature of a TPU layer on the shoe side which prevents the risk of cleats sliding on carbon soles. Their anti-slip surface on the pedal side offers extra safety and stability when walking. - Use: Road - Material: Polyamide + TPU - Lateral adjustment: 4mm - Longitudinal adjustment: 9mm - Weight (pair + fasteners): 68g
$27.99
RaceFace Chester Pedal Spindle Kit Left/Right
$29.95
The Ergon TP1 Pedal Cleat Tool is the first tool for precisely and easily adjusting cycling shoes cleats. The ergonomically correct position of the feet on the pedals plays a crucial role in injury prevention and is also important for maximizing both performance and comfort.
$30.00
Dimension Combo Pedal Sets are assembled with size large toe clips, straps and reflectors. - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 475g
$33.99
Replacement axles for Race Face Atlas pedals.
$37.00
Dimension Combo Pedal Sets are assembled with size large toe clips, straps and reflectors. - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 520g
$39.95
Wellgo WPD-823 Clipless Mountain Pedals. - Includes 98A cleats, Shimano SM-51 compatible - Dual-spring release/entry tension adjustment - Four degrees of Rotation - 9/16"
$39.99
Problem Solvers Deckster pedal adapters. Converts SPD-compatible pedals to platform pedals for casual cruising. - Works with 2-bolt, SPD-style cleats, such as Time, Shimano, Crank Brothers, Wellgo and others. Not compatible with Speedplay - Cleats not included - 85 x 95 x 10mm platform - Hardware included, cleats not included
$39.99
The RaceFace Ride pedal features a slim nylon-composite platform, and offers a concave and lightweight design for legitimate performance. - Molded traction pins give you all the grip you need without risk of damaging your shoes or shins - Durable Cro-Mo steel axle features a standard 9/16” pedal thread and serviceable internal parts - 9/16"
$40.00
Replace worn-out spindles or customize your stance width, with these kits for iSSi Road pedals. - Chromoly spindles - Sealed cartridge bearing and bushing in an alloy cartridge - Compatible only with iSSi Road pedals - Installs with iSSi Road spindle tool (TL5499) - Pedal Spindle: 9/16" - Spindle Material: Chromoly Steel
$41.00
Secure your everyday cycling confidence and comfort in the essential urban pedal from LOOK. Geo City is a lightweight, upgradeable and affordable platform pedal but with all the style, quality and durability that’s made LOOK pedals the champion’s choice for decades, and the best out on the city streets today. - Technology: Flat pedals - Body: Composite - Traction: Composite - Spindle: Chromoly+ - Surface area: 110x107mm - Weight (pedal): 165g - Weight (pair): 330g
$42.75
MSW Thump composite pedals feature a concave shape and tall pins to provide a "just-right" amount of traction--enough for the rigors of riding off-road--but with in-mold nylon pins to keep calves laceration-free on more casual rides. Balance doesn’t have to mean boring! - Tough nylon composite body with in-mold pins - Chromoly steel, 9/16” spindles, sealed cartridge bearings and nylon bushings - Platform size = 118 x 99 x 19 mm - Body: 18.5 mm thick with 2.5 mm of concavity for great control and comfort - Black - Made in Taiwan
$45.00
The soft rubber Activ Grip City pads feature our exclusive LOOK Activ Grip technology developed in partnership with Vibram and are compatible with our Geo City platform pedals. They offer the best foot-to-pedal connection we have ever designed, with exceptional grip, wear resistance and durability.  
$45.00
The Activ Grip Trail Pads are compatible with our Trail Grip platform pedals. Built from extremely strong and durable material and designed in collaboration with outdoor specialist Vibram, they offer exceptional traction on the toughest rides. Their concave geometry is enhanced with large rubber lugs and composite studs for optimal foot stability and extreme durability to take on the challenges of any terrain.
$49.00
Light, impact resistant. New for 2018 is the Synth Pedal. An injection molded, nylon reinforced platform that is light, impact resistant and won’t break the bank. Modeled after our Scarab pedal, the Synth features a large platform with true concave and our proprietary pin system. It uses the same high-end axle and bearing assembly as on our Scarab and Contact models so you can count on long-life and smooth performance, with common serviceability components available from Chromag.
$49.00
- Injection molded, nylon reinforced platform that is light, impact resistant and won’t break the bank - Modelled after the Scarab pedal, the Synth features a large platform with true concave and our proprietary pin system - It uses the same high-end axle and bearing assembly as on our Scarab and Contact models - 15mm thick at platform centre, concave design - 110mm x 107mm
$49.99
Widen your Q-factor to 57mm. - Long spindles are 5mm longer than standard. - The kit includes: 1 pair long spindles + refresh kit (Enduro cartridge bearings, igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double shot, model years 2010-present - Weight: 112g per pair - Spindle material: forged SCM 435 chromoly steel - Q-factor: 57mm
$49.99
Size specific composite platform pedal with optimal shoe/pedal interface. - Optimal surface area - Minimal profile 13mm thin - 9 hex traction pins per side - Premium bearings & seal system - Stamp small recommended for shoe sizes: 5-10 (us) // 37-43 (eu) - Body Material: Composite - Footprint: 111mm x 114mm - Hex Traction Pins: 9 per side (mounted from back) - Inner Bearing Type: Igus LL-glide bearing - Outer Bearing Type: Enduro cartridge bearing - Shoe Size: US 5-10 // EU 37-43 - Spindle Material: Forged scm 435 chromoly steel - Warranty: 5 years - Weight: 329g per pair
$49.99
Size specific composite platform pedal with optimal shoe/pedal interface. - Optimal surface area - Minimal profile 13mm thin - 9 hex traction pins per side - Premium bearings & seal system - Stamp small recommended for shoe sizes: 5-10 (us) // 37-43 (eu) - Body Material: Composite - Footprint: 100mm x 100mm - Hex Traction Pins: 9 per side (mounted from back) - Inner Bearing Type: Igus LL-glide bearing - Outer Bearing Type: Enduro cartridge bearing - Shoe Size: US 5-10 // EU 37-43 - Spindle Material: Forged scm 435 chromoly steel - Warranty: 5 years - Weight: 299g per pair
Page 1 of 3 Next page