Your Search: "echo"

- Rim strips from Trialtech. - Heavy duty plastic rim tape is tough yet flexible. - Strong heat bonded join with a large enough hole for all types of valve. - Matte finish on one side and gloss on the other. - Very tough, durable, and also waterproof. - Available in Black or White. - Front width 25mm, rear width 40mm. - 24" width 35mm.

- Superlight rim tape from Jitsie. - Extremely light nylon material is still strong enough to resist tearing and bubbling. - Significantly lighter than competitor's rim tapes. - Strong heat bonded join with hole for all valve types. - Silver/grey with printed Jitsie logos on one side and plain blue finish on the other. - 30mm front width, 42mm rear width.

- The updated Inspired Pro V2 rim offers excellent strength and value for street trials. - Un-eyeletted construction saves over 50g when compared with eyeletted rims. - Un-drilled double wall construction is very stiff and strong, ideal for street riding. - 36mm wide profile gives good anti-roll performance even at low tire pressures. - For use with disc brakes only. - Available in gloss black anodized finish with white Inspired graphics. - 32h spoke drilling only.

- Replacement star fangled nut for use inside fork steerer tubes to allow pre-load of headset bearings. - Standard M6 x 1.0 thread. - For sizing, the star nut should be 1-3mm larger than the internal diameter of your fork steerer.

- Super lightweight 24" rear rim from Jitsie. - Constructed from high quality 6061 T6 aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 48mm width provides excellent stability and helps prevent tire roll. - Custom large parallelogram holes keep the weight to a minimum. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Large sidewall area for maximum brake pad contact. - Available in 32 hole spoke drilling only. - Anodized black finish with Jitsie stickers around valve holes. Please Note: Due to the profile of these rims, the ridge near the spoke holes can make it difficult to fit a spoke wrench on standard length nipples. Because of this, we recommend lacing these rims with 14mm or 16mm long nipples.

- Designed completely from scratch by Trialtech to provide a new level of stiffness and rigidity in trials rims whilst maintaining the lowest possible weight. - Tested and developed in competition by World Champion Jack Carthy and on street by Joe Prattley. - Unique un-drilled double wall design gives unrivaled strength and stiffness compared to competitor’s single wall rims (up to 3 times more lateral stiffness!). - Custom butted center section adds strength around the spoke holes for improved durability. - 31mm wide profile gives a good balance of low weight and tire performance. - Sleeved joint helps maintain concentricity and maximizes strength. - Available in sandblast black anodized finish with Carthy Signature laser etched logos. - Available in 28h or 32h spoke drilling. - For use with rim or disc brakes.

- Super lightweight 19" rear rim from Jitsie. - Constructed from high quality 6061 T6 aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 48mm width provides excellent stability and helps prevent tire roll. - Custom large parallelogram holes keep the weight to a minimum. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Large sidewall area for maximum brake pad contact. - Available in 32 hole spoke drilling only. - Anodized black finish with Jitsie stickers around valve holes. Please Note: Due to the profile of these rims, the ridge near the spoke holes can make it difficult to fit a spoke wrench on standard length nipples. Because of this, we recommend lacing these rims with 14mm or 16mm long nipples.

- Super lightweight 26" front rim from Jitsie. - Constructed from high quality 6061 T6 aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 33mm width provides good stability and helps prevent tire roll. - Custom large parallelogram holes keep the weight to a minimum. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Large sidewall area for maximum brake pad contact. - Available in 28 hole spoke drilling only. - Anodized black finish with Jitsie stickers around valve holes. Please Note: Due to the profile of these rims, the ridge near the spoke holes can make it difficult to fit a spoke wrench on standard length nipples. Because of this, we recommend lacing these rims with 14mm or 16mm long nipples.

- The Inspired Pro V2 rim offers excellent strength and value. - Updated V2 version tested and proven by John Langlois. - Double wall angular profile for increased strength and stiffness. - Un-eyeletted construction saves over 50g when compared with eyeletted rims. - 36mm width gives good anti-roll performance even at low tire pressures. - Available in gloss black anodized finish with white 'Inspired' graphics. - For use with disc brakes only. - 32h spoke drilling only. - Not tubeless compatible.

- Super lightweight 26" rear rim from Jitsie. - Constructed from high quality 6061 T6 aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 48mm width provides excellent stability and helps prevent tire roll. - Custom large parallelogram holes keep the weight to a minimum. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Large sidewall area for maximum brake pad contact. - Available in 32 hole spoke drilling only. - Anodized black finish with Jitsie stickers around valve holes. Please Note: Due to the profile of these rims, the ridge near the spoke holes can make it difficult to fit a spoke wrench on standard length nipples. Because of this, we recommend lacing these rims with 14mm or 16mm long nipples.

- Durable double wall rim from Inspired. - As fitted to the Inspired Flow bikes. - Double wall, high quality aluminum construction for maximum strength and stiffness. - Un-eyeletted construction saves over 50g when compared with eyeletted rims. - 32mm wide profile. - Suitable for disc or rim brake use, its parallel sidewalls make it ideal for street trials bikes with rim brakes. - Black anodized finish with laser etched Inspired logo. - 32h spoke drilling only.

- Super lightweight 20" front rim from Jitsie. - Constructed from high quality 6061 T6 aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 33mm width provides good stability and helps prevent tire roll. - Custom large parallelogram holes keep the weight to a minimum. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Large sidewall area for maximum brake pad contact. - Available in 28h and 32h spoke drilling. - Anodized black finish with Jitsie stickers around valve holes. Please Note: Due to the profile of these rims, the ridge near the spoke holes can make it difficult to fit a spoke wrench on standard length nipples. Because of this, we recommend lacing these rims with 14mm or 16mm long nipples.

- Replacement "Spanish Style" press-fit bottom bracket from Trialtech. - ISIS bottom bracket to fit frames with Spanish style BB shells (Echo, GU etc.). - High quality manufacturing with excellent tolerances and finishing quality. - Custom machined, lightweight M15 cromoly steel axle keeps weight down. - 132mm axle length is 8mm longer than Echo press fit bottom brackets, which gives additional clearance for certain crank/frame combinations with low clearance. - 6061 aluminum 'Top Hat' axle spacers maintain correct bearing preload and crank fitment. - Orientation of 'Top Hat' spacers can be changed to work with standard screw-on freewheel cranks or the Echo splined freewheel system. - Includes M15 steel crank bolts. Please note: When fitting axle spacers, the wide end must face inwards towards the frame when using standard screw-on freewheel and outwards when using the Echo splined freewheel system. Incorrect fitting of the spacers will void the warranty.

- Lightweight 20" front rim from French brand Crewkerz. - Constructed from high quality aluminum for improved durability and brake performance. - Un-eyeletted design and single wall construction save weight. - 31mm width provides good stability and helps prevent tire roll. - "H" shaped rim profile improves strength and stiffness of sidewalls. - Custom rectangular holes reduce weight. - Large 9.5mm sidewall area for good brake pad contact. - Available in 32 hole spoke drilling only. - Anodized black finish.

- Replacement bearing to fit Spanish bottom brackets only. - Compatible with all newer Echo, Zoo, Czar and GU frames as well as some others. - High quality construction with double seals. - For use on the drive or non-drive side. - Sold singly. - OD:37mm, ID:22mm, Width:9mm

- Splined freewheel from Crewkerz to fit their AS30 cranks. - Uses 9 steel pawls with a 45t ratchet to create 135 engagement points for ultra quick pedaling response! - Machined from a custom mold from tough CroMo steel for maximum durability. - Extra strong springs provide reliable engagement and give the freewheel a distinctive loud sound. - Unlike most other freewheels it uses high quality sealed bearings for improved durability and protection from dirt and grit. - Splined design makes it much easier to install and remove than traditional threaded freewheels. - Compatible with Shimano HG spline style cranks such as Crewkerz, Clean, and Bonz, will not fit Echo splined cranks. - Supplied with a spacer to be used between the crank and freewheel. - Anodized black finish. - Available in 18t only. Please Note: This freewheel must be bedded in before trials use, which ensures any excess grease used when assembling the freewheel works away from the mechanism. This can be done by riding the freewheel around 'normally' for a few hours, both freewheeling and engaging the mechanism gently. If the freewheel is subjected to trials use before it has been bedded in, the pawls may not engage correctly, causing the freewheel to skip, which can damage the pawls and ratchet. Failure to bed the freewheel in correctly will void the warranty.

- Light sprung chain tensioner from Trialtech. - Single speed specific chain tensioner. - Constructed from high grade aluminum alloy, spring steel and chromed steel. - Multi coil spring to prevent loss of tension over time, a common problem with other tensioners. - Single sided cage design saves weight and allows the chain to be taken off quickly for easier wheel fitting/removal. - Runs on two plastic jockey wheels for minimum noise. - Slim design to help reduce the chance of damage during riding. - Adjustable chain line ensures compatibility with most setups. - Custom mount design allows the tensioner to be tightened securely against the hanger without requiring the delicate positioning tab that can be damaged or limit performance on competitor's products. - The model without hanger mount fits 2014 Fourplay Tensioner Mounts and Trialtech Sport Sprung Tensioner arms. - The model with hanger mount fits all frames with a standard derailleur hanger. - Gloss black anodized finish.

- Lightweight and extremely minimal single speed spacer kit from Trialtech. - Includes a range of spacer sizes to allow you to fine tune your chain line: 2x 10mm, 1x 6mm, 1x 5mm and 1x 3mm. - Great for single speed conversions or fine tuning your chainline. - CNC machined from high grade aluminum alloy, then anodized to prevent corrosion. - Available in Gloss Black only with laser etched Trialtech logo on the 10mm spacers. - Cassette lockring sold separately.

- Custom designed sprung chain tensioner as fitted to Inspired Team bikes. - Developed and proven by Inspired Team riders. - Constructed from high grade 7075 and 6061 aluminum alloy. - High tension coil spring provides excellent chain tension. - Single sided cage saves weight and allows the chain to be taken off quickly for easier wheel fitting/removal. - Runs on two plastic jockey wheels for minimum noise and low drag. - Slim, integrated design helps reduce the chance of damage during riding. - Extended cage improves ergonomics and further aids chain removal. - Fits directly onto Skye V3/V3.5, Fourplay/Hex (2014-onwards) and Link (2023-onwards) frames. - Satin black anodized finish. - 16t (Fourplay, Skye, Link) or 18t (Hex) compatible versions available. - Includes frame fixture bolts.

- Lightweight ISIS crank bolts from Jitsie. - Designed and manufactured in Belgium as part of the Jitsie Race range. - Compatible with all M15 threaded ISIS bottom brackets. - Machined from high quality aluminum, a conical head and cutouts keep weight to an absolute minimum. - Supplied with superlight aluminum washers, saving further weight. - Fitted for a 10mm allen key instead of 8mm used on most other crank bolts. - Available in anodized black or red with laser-etched Jitsie logos. - Sold as a pair.

- Great value forged cranks from Jitsie. - Constructed from forged 7075 T6 aluminum for optimal stiffness. - Material removed from the back of the cranks saves weight while maintaining strength in key areas. - 1.37" x 24tpi threaded section suitable for all trials freewheels or threaded cogs. - Matte anodized black finish with Jitsie logos. - Compatible with all ISIS bottom brackets. - Available in 160mm, 165mm, 170mm, and 175mm lengths. Please note that the minimum required thread contact between crank arm and sprocket/freewheel is 9mm, and a 1.37" sprocket/freewheel must be used. Failure to adhere to this instruction will damage the cranks threads and this is not covered under warranty.

- Lightweight half bashring from Crewkerz as found on their AS30 cranksets. - CNC-machined from 7075-T6 aluminum for maximum strength and durability. - UCI competition style can be fitted to suit left or right footed riders. - Small pockets on each side mate with the pins on Crewkerz AS30 cranks to keep the bashring oriented perfectly at all times. - 3mm wide base with 6mm outer edge. - CNC cutouts in center section reduce weight and improve aesthetics. - Designed for use with pre-2018 Crewkerz AS30 cranks, may also work with other cranks. - Available in 18t with red anodized finish. Please Note: These are designed for use with pre-2018 Crewkerz AS30 cranksets. The small pocket on the ring that mates with the pin needs to be modified slightly (enlarged) to fit the newer AS30 cranks.

- Splined cog from Crewkerz. - CNC machined from super tough Cro-Moly steel for maximum durability. - Wide base gives a greater contact area between hub and sprocket, helping prevent 'dig-in' problems associated with narrow based sprockets. - Compatible with Crewkerz and Bonz hubs as well as any other hub that uses the industry standard Shimano HG spline pattern. - Compatible with all 1/8" and 3/32" chains. - Black finish with laser etched product information.

- Light, affordable half bashring from Trialtech. - Great value half bashring to fit nearly all screw-on cranks. - Full CNC machined aluminum alloy construction. - UCI competition style can be fitted to suit left or right footed riders, however it only covers one side of your freewheel/sprocket for maximum weight saving! - 5mm wide base with 5mm outer edge. - CNC scoops in center section reduce weight and improve aesthetics. - Built-in lip allows the bashring to be run with any freewheel. - Matt black anodized finish with laser etched Trialtech logo. - Available in 18T (88mm effective diameter).

- Replacement steel crank bolts from TruVativ. - Fitted for an 8mm allen key. - Includes steel washers. - Available in M12 and M15 sizes. - Sold as a pair.

- Quality 16t freewheel from Trialtech. - Rear freewheel as fitted to many Inspired complete bikes. - High quality, heat treated steel pawls engage into a tough steel ratchet. - Available with 72 engagement points per revolution with a proven 6 pawl design or 108 engagement points per revolution with a proven 9 pawl design. - Quick engagement and durable operation. - Industry standard 1.37" x 24tpi thread. - 4 inset removal pockets. - Black finish. - Available in 16T only. Please Note: This freewheel is designed for use as a rear freewheel. It can also be used as a front freewheel by kids and light riders but durability may be significantly less for larger riders. Also Note: This freewheel must be bedded in before trials use, which ensures any excess grease used when assembling the freewheel works away from the mechanism. This can be done by riding the freewheel around 'normally' for a few hours, both freewheeling and engaging the mechanism gently. If the freewheel is subjected to trials use before it has been bedded in, the pawls may not engage correctly, causing the freewheel to skip, which can damage the pawls and ratchet. The bedding in process can be expedited by spraying a light oil like GT85 or WD40 between the center and outer teeth of the freewheel and rotating it. Failure to bed the freewheel in correctly will void the warranty.

- High quality, CNC machined cromoly snail cam from Trialtech. - Gloss nickel, hard coated finish for extra durability. - A series of incrementally smaller drilled holes are designed to reduce weight without compromising strength. - Notched design to hold your wheel in position and ensure that it doesn't move, designed to be a 'fit-and-forget' product. - High resolution tooth pattern provides fine chain adjustment. - Will fit most bikes with a 10mm axle designed to work with snail cam tensioners. - Sold individually to allow you to tailor your setup to your specific needs.

- CNC machined from super tough hardened Cro-Moly to offer a high level of quality and durability. - A shot blasted surface finish after machining increases the surface hardness and improves durability. - Wide 4.5mm base gives a greater contact area between hub and sprocket, reducing interface pressure and helping prevent 'dig-in' problems associated with narrow based sprockets. - Tapered design gives maximum strength, while CNC machined slots (17 and 18T models only) help keep the weight down. - Compatible with all 1/8" and 3/32" chains. - Industry standard Shimano HG spline pattern. - Can also be run in a cassette for your main drive gear. The 4.5mm wide base is the same spacing as an 9 speed Shimano cassette. - Stylish laser etched logos show great attention to detail. Please Note: These may be supplied with a silver or black finish.

- Replacement master link for KMC singlespeed chains. - Allows the chain to be conveniently removed without a chain tool. - Includes connecting link and retaining clip. - Available in 3/32" (silver) and 1/8" (grey) sizes.

- Singlespeed chain used by many trials riders. - Spec'd on many complete trials bikes such as Inspired bikes. - The successor to the very popular Z610 HX chain. - "Stretch Proof" design helps prevent stretch in the plates, meaning chain adjustments are needed less frequently, especially when the chain is new. - Relatively light weight but still quite durable. - Features mushroom pin rivets to eliminate splayed links. - Also supplied with a re-usable master link that allows for easy installation and removal. - 1/2" x 3/32" - 112 links.